BMW 750Li Parking brake won't release Inspection costs between $80 and $90 on average. The parts and labor required for this service are.
Recently,I did some searcher about topic:how to reset iDrive warning message after replacing brake pads.And i found the following information at bimmerfest.com,and at the end of article i will put the orginal link.The author tried it on my E60 and it worked perfectly. I am thinking that other models with Idrive will work the same way.
Procedures of reset iDrive warning message after replacing brake pads:
Firstly with the ignition switched on, set the odometer trip meter back to zero by pushing it once. Then switch the ignition back off again. (I found this step was critical, otherwise I couldn’t get to the “Service” menu).
- Switch the ignition on (so that the battery, Oil and Parking brake lights are displayed) and the key is ready to start the engine – but don’t actually start the car.2. Press the odometer reset button for between 5 and 10 seconds until a yellow triangle with an exclamation mark in the centre appears in the top window between the clocks (where the outside temperature / time or date normally appears) – this is the “Service” icon.3. Release the odometer button briefly and press again straight away which brings up a picture of the Brake Fluid symbol (same as the one that the i-drive shows when you look at the Service menu).4. If you want to reset the Brake Fluid interval for another 2 years then keep holding the odometer button until the word “RESET?” appears at the bottom of the lower window.5. Release the button briefly and push it in again and hold for about 5 – 10 seconds until the new date appears in the bottom window. You can then switch the ignition off and the new Brake Fluid date will appear in the service menu on the i-drive screen next time you switch on.6. If you want to reset the Oil, Microfilter or Brake Pad indicators then you will need to follow the same sequence as steps 1 and 2 above, but when you get to step 3 and the brake Fluid icon appears, just release the button and press again and the next service item will appear.7. You can continue releasing and pressing the button until the required service item icon appears for the one you want to reset. As soon as it does then hold in the button in until the word “RESET?” appears again as in step 4 above. Once the word “RESET?” has appeared, you need to release the button briefly and hold it in again for about 5 – 10 seconds until it is replaced by the new service interval figure (as per step 5 above).Hints & Tips
Before actually resetting anything, go through steps 1, 2 and 6 above until you are familiar (and sure) what you want to reset. Practice this a few times and note down in what order the icons appear after the initial “Service” icon appears.If you do happen to hold the button down too long against an item you don’t want to reset and the “RESET?” appears, just leave the button alone for 10 seconds or so and it will not let you reset the item. (Alternatively just switch the ignition off and start again).Sometimes if you have not released and pressed the button again quickly enough, when you hold it down again the German technical writing will appear after about 15 – 20 seconds instead of the Service item icon you were expecting. (If this happens just switch off the ignition and start again).Once you are sure what item you want to reset and are confident of the sequence, then give it a go. If you do hesitate between releasing and pressing the button at any time, you will have to go back to the beginning and start again as “he who hesitates is lost”.
http://www.bimmerfest.com/forums/showthread.php?t=133613
FromAuto Repair Technician Home, postHow To Reset iDrive Warning Message After Replacing Brake Pads
Readers who read this article also read:
This is a question and answer about enet cable programing
Question:
Any one has programmed all car with ista-p with enet cable successful
it’s safe to do it with enet cable?
it’s safe to do it with enet cable?
BMW F10 530DX
Answer:
ICOM is a separate computer which handles all protocols itself and has connection to a car through multiple busses (D-CAN, K-CAN, ENET) at the same time. It also has internal measurement for car voltage, etc.
F10 is able to talk via D-CAN and ENET. Strictly speaking both of these are connected to ZGM which then “translates” messages and forward to other units in a car via appropriate buses. As long as your ZGM is functioning properly there is no difference. However ENET bus needs much more complicate software to run, and early ZGMs do have issues to be programmed over this bus (you can use search on this forum to find workarounds).
So basically, ICOM can monitor car voltage, ignition status and other things itself and stop communication with a car if prerequisites are not met. ENET cable will pump data to a car in any case. If your power supply has ample amperage to keep constant car voltage, this may not be an issue.
As Spirit said flashing a car is always a risk. Its just smaller (and potentially easier recoverable) with the right tools.
I personally prefer ISTA+ for flashing because its “run and enjoy”. It knows which units need to be programmed with ignition on and which with it off. It also runs all required initializations afterwards. With E-Sys you more or less need to know all of that yourself and do manually. But when flashing fails seriously, E-Sys is the only tool to do recovery.
Good to know: INPA K+DCAN cable vs. ENET cable vs. BMW ICOM
Link: http://blog.obdii365.com/2017/09/13/k-dcan-cable-vs-enet-cable-vs-bmw-icom/
Attachment: BMW F10 coding cheat sheet 2011
– Add Paddle Shifter Functionality for retrofit Sport Paddles
FA (VO) Replace 205 with 2TB.
Code new FA in ECUs ICM, EGS, GWS, and SZL
– Add SAT functionality
FA (VO) Replace 205 with 2TB.
Code new FA in ECUs EGS, and GWS
– Automatic High beam Assist Headlights (Car must have KAFAS camera which supports High Beam Assistant, Lane Departure Warning, and
Speed Limit Information. Without this camera system installed, there is no KAFAS module)
2011-12 (CIC)
FRM => 3050 => FLA_VERBAUT => aktiv
FRM => 3050 => FLA_AUTO_AKTIV => automatisch
KAFAS2 => 3050 => FLA_ON_OFF => aktiv
HU_CIC => 3000 => HIGH_BEAM_ASSISTANT => aktiv
2012-13 (NBT) and 2014 LCI
FRM => 3050 => FLA_VERBAUT => aktiv
FRM => 3050 => FLA_AUTO_AKTIV => automatisch
KAFAS2 => 3050 => FLA_ON_OFF => aktiv
HU_NBT => 3000 => HIGH_BEAM_ASSISTANT => aktiv
– Automatic Parking Brake Release (Some 2011-12 cars)
DSC => 3000 => Funktion_AutomaticDriveawayRelease_aktiv => aktiv
EMF => 3000 => ADR_AKTIV => ADR_ein
– Auto Start-Stop function to start as last used
CAS => 3000 => TC_MSA_MEMORY => aktiv
2014 LCI
Parking Brake Release Cable
Already incorporated
– Auto Start-Stop OFF by default
CAS => 3000 => TC_MSA_DEFAULT_OFF => aktiv
– Blind Spot Detection at lower speeds (17 mph min)
ICM => 3000 => Hc2_i_CPar_Aktiv_v_low => 25 kmh, or
ICM => 3000 => HcSwcCPar_i_Hc2_Aktiv_v_low => 25 kmh
– Change Nav voice from US to UK English
2011-12 (CIC)
HU_CIC => 3000 => VOICE_LANGUAGE_RR_US => aktiv
2012-13 (NBT) and 2014 LCI
HU_NBT => 3000 => LANGUAGE_ENGLISH_UK => master
HU_NBT => 3000 => LANGUAGE_ENGLISH_US => nicht_aktiv
– Disable iDrive legal disclaimer
2011-12 (CIC)
HU_CIC => 3001 => LEGAL_DISCLAIMER_TIME => kein_ld
2012-13 (NBT) and 2014 LCI
HU_NBT => 3001 => LEGAL_DISCLAIMER_TIME => kein_ld
– Disable Night Vision camera legal disclaimer
2011-12 (CIC)
HU_CIC => 3001 => MACRO_NIVICAM_LDISCLAIMER => kein_ld
2012-13 (NBT)
HU_NBT => 3001 => MACRO_NIVICAM_LDISCLAIMER => kein_ld
– Disable Rear and Side view camera legal disclaimer
2011-12 (CIC)
HU_CIC => 3001 => MACRO_CAM_LEGALDISCLAIMER => kein_ld
2012-13 (NBT) and 2014 LCI
HU_NBT => 3001 => MACRO_CAM_LEGALDISCLAIMER => kein_ld
– Disable seat belt status display – driver and pax
ACSM => 3000 => Gurtzustandsanzeige_Fahrer_GWF_GZA_FA => nicht_aktiv
ACSM => 3000 => Gurtzustandsanzeige_Beifahrer_GWF_GZA_BF => nicht_aktiv
– Disable seat belt reminder – driver and pax
ACSM => 3000 => SBR_FA_GWF_SBR_FA (or SeatBeltReminder_SBR_Fahrer) => nicht_aktiv
ACSM => 3000 => SBR_BF_GWF_SBR_BF (or SeatBeltReminder_SBR_Beifahrer) => nicht_aktiv
– Disable sound on disconnect SB – driver and pax
ACSM => 3000 => SPW_FA (or SBR_PreWarning_Fahrer) => nicht_aktiv
ACSM => 3000 => SPW_BF (or SBR_PreWarning_Beifahrer => nicht_aktiv
– Display digital speed in instrument cluster (bottom center in basic, bottom of Speedo in Extended and Multi-Function)
KOMBI => 3000 => BC_DIGITAL_V => aktiv
– Enable Adaptive Brake Lights
FRM => 3050 => ESS_ERSCHEINUNGSBILD => bremslicht blinkend
– Enable DVD in motion
2011-12 (CIC)
HU_CIC => 3000 => SPEEDLOCK_X_KMH_MIN => value = FF
HU_CIC => 3000 => SPEEDLOCK_X_KMH_MAX => value = FF
HU_CIC => 3000 => VIDEO_NUR_MIT_HANDBREMSE => nicht_aktiv
2012-13 (NBT) and 2014 LCI
HU_NBT => 3000 => SPEEDLOCK_X_KMH_MIN => value = FF
HU_NBT => 3000 => SPEEDLOCK_X_KMH_MAX => value = FF
HU_NBT => 3000 => VIDEO_ HANDBRAKE => nicht_aktiv
– Enable Fog Lights with High Beams
FRM => 3050 => NSW_AUS_BEI_FL => nicht_aktiv
– Enable current position (GPS and Street Name) menu item (Navigation Display => options)
2011-12 (CIC)
HU_CIC => 3000 => NAVI_POSITION_MENU => aktiv
2012-13 (NBT)
HU_NBT => 3000 => NAVI_POSITION_MENU => aktiv
2014 LCI
Already in iDrive
– Enable HUD Entertainment and Telephone display
KOMBI => 3000 => HUD_ENTERTAINMENT_ENABLE => aktiv (Enables radio menu)
KOMBI => 3000 => HUD_TELEFONBUCH_ENABLE => aktiv (Should display full contact list)
KOMBI => 3000 => HUD_TELEFONANRUF_ENABLE => aktiv (Enables recent calls list to be displayed)
KOMBI => 3000 => HUD_SPRACHEINGABE_ENABLE => aktiv (Display voice command conformation information in HUD)
– Enable HUD Turn Signals display
2011-12 (CIC)
![Bmw Bmw](/uploads/1/2/6/8/126884093/100038420.jpg)
KOMBI => 3000 => BLINKER_HUD_ENABLE => aktiv
HU_CIC => 3000 => HUD_TURNSIGNAL => aktiv
2012-13 (NBT)
KOMBI => 3008 => HUD_PIA_BLINKER => aktiv
KOMBI => 3000 => BLINKER_HUD_ENABLE => aktiv
HU_NBT => 3001 => HUD_TURNSIGNAL => aktiv
– Enable key fob and driver side door handle to close the trunk (requires powered trunk)
HKFM => 3010 => TASTER_FBD => aktiv
HKFM => 3010 => SCH_TOEHKI => aktiv
HKFM => 3010 => SCH_FBD => aktiv
– Enable key fob and driver side door handle to fold mirrors* and close windows and moon roof
CAS => 3003 => KOMFORTSCHLIESSUNG_FB => aktiv
CAS => 3003 => KOMFORTSCHLIESSUNG_PA => aktiv
FRM => 3020 => ASP_BEIKLAPPEN_BEI_KOMFORTSCHLIESSEN => aktiv
* To change mirror fold delay
CAS -> 3003 -> KMFRT_SCHLIESSEN => Werte= 05 for 0.5 sec, 0A for 1 sec, 0F for 1.5 sec
– Enable Pressure and Temperature Readings to the TPMS Screen
2011-12 (CIC)
HU_CIC => 3001 => RDC_SAFETY => aktiv
2012-13 (NBT) and 2014 LCI
HU_NBT => 3001 => RDC_SAFETY => aktiv
– Enable Sports Display (Power* & Torque* Meters) in the Vehicle Info screen.
(For N55 only. For N63 cars the gauges appear, but do not function)
2011-12 (CIC)
HU_CIC => 3000 => EFF_DYN_SPORT_CID => aktiv
HU_CIC => 3000 => EFF_DYN_SPORT_UNIT => aktiv
2012-13 (NBT)
HU_NBT => 3000 => EFF_DYN_SPORT_CID => aktiv
HU_NBT => 3000 => EFF_DYN_SPORT_UNIT => aktiv
2014 LCI
Already in iDrive
* To change units displayed to be ft lb and hp
KOMBI => 3008 => DREHMOMENT => lb_ft (displays ft lb)
KOMBI => 3008 => LEISTUNG => ps (displays hp)
– Enable Sports Display menu when switching to sport driving mode
KOMBI => 3000 => SPA_SPORT_ENABLE => aktiv
– Enable video playback via USB Port and with various video formats
HU_NBT => 3003 => API_USB_VIDEO => both
HU_NBT => 3000 => ENT_CODEC_XVID => aktiv
HU_NBT => 3000 => ENT_CODEC_VCD => aktiv
(Will play any format (mpg, avi, mkv, divx . Also at HD Resolution)
– Halos full brightness even when headlights are on
FRM => 3060 => U_EFF_POL => wert_02__100%
– Opening doors will not interrupt window roll up (Front and Back)
FRM => 3030 => FH_TUER_AUF_STOP_MAUT => nicht_aktiv
JBBF => 3070 => FH_TUERAUF_STOP_MAUT => nicht_aktiv
– Rear view camera always available
PDC => 3009 => D_SCHWELLE_2 => Werte => FF
PDC => 3009 => V_SCHWELLE_2 => Werte => FF
– Subtle orange lines at the bottom of Extended (6WA) or Multifunction (6WB) display during the day (2013 Default is grey)
KOMBI => 3000 => HINTERGRUND_FARBE_TAG => orange
– Subtle grey lines at the bottom of Extended (6WA) or Multifunction (6WB) display during the night (2013 Default is orange)
KOMBI => 3000 => HINTERGRUND_FARBE_NACHT => grau
– Subtle grey lines at the bottom of Extended (6WA) or Multifunction (6WB) always in day mode
KOMBI => 3007 => DIM_NACHT_EIN => Werte=FF
– Splash animation on the iDrive screen upon system load: Variant1 = M logo, Variant7 = White BMW logo, Variant8 = Brown bmw logo (same as
HU_CIC), Variant9 = Merry Xmas
2011-12 (CIC) (function not found)
2012-13 (NBT) and 2014 LCI
HU_NBT => 3001 => STARTUP_EMBLEM => variant_01 (default: _0)
– Turn off power (radio and iDrive) when opening door
2011-12 (CIC)
CAS => 3000 => TC_LOGIC_KLR_OFF_DOOR => aktiv
2012-13 (NBT) and 2014 LCU
CAS => 3000 => TC_LOGIC_KLR_OFF_DOOR => aktiv
– Transfer telephone ringtone to the car
2011-12 (CIC)
CMB_MEDIA => 3001 => INBAND_RINGING => aktiv
2012-13 (NBT)
HU_NBT => 3003 => INBAND_RINGING => aktiv
– Unlock doors when engine is stopped (doors unlock linked to doors automatically locked by iDrive)
CAS => 3002 => ER_KEYOUT_AUTOVR => aktiv